View the following exhibit
Given the configurations shown in the exhibit, what can you conclude from the installation targets Install On the column? The Install On column value represents successful installation on the managed devices Policy seq#3 will be installed on all managed devices and VDOMs that are listed under Installation Targets Policy seq#3 will be installed on the Trainer[NAT] VDOM only Policy seq#3 will be not installed on any managed device.
Which two settings must be configured for SD-WAN Central Management? (Choose two.) SD-WAN must be enabled on per-ADOM basis You can create multiple SD-WAN interfaces per VDOM When you configure an SD-WAN, you must specify at least two member interfaces. The first step in creating an SD-WAN using FortiManager is to create two SD-WAN firewall policies.
How will FortiManager try to get updates for antivirus and IPS? From the list of configured override servers with ability to fall back to public FDN servers From the configured override server list only From the default server fdsl.fortinet.com From public FDNI server with highest index number only.
When an installation is performed from FortiManager, what is the recovery logic used between FortiManager and FortiGate for an FGFM tunnel? After 15 minutes, FortiGate will unset all CLI commands that were part of the installation that caused the tunnel to go down. FortiManager will revert and install a previous configuration revision on the managed FortiGate. FortiGate will reject the CLI commands that will cause the tunnel to go down. FortiManager will not push the CLI commands as a part of the installation that will cause the tunnel to go down.
Which two statements about the scheduled backup of FortiManager are true? (Choose two.) It does not back up firmware images saved on FortiManager. It can be configured using the CLI and GUI. It backs up all devices and the FortiGuard database. It supports FTP, SCP, and SFTP.
An administrator would like to create an SD-WAN using central management in the Training ADOM.
To create an SD-WAN using central management, which two steps must be completed? (Choose two.) Specify a gateway address when you create a default SD-WAN static route Enable SD-WAN central management in the Training ADOM Configure and install the SD-WAN firewall policy and SD-WAN static route before installing the SD-WAN template settings Remove all the interface references such as routes or policies that will be a part of SD-WAN member.
An administrator wants to delete an address object that is currently referenced in a firewall policy. What can the administrator expect to happen? FortiManager will not allow the administrator to delete a referenced address object FortiManager will disable the status of the referenced firewall policy FortiManager will replace the deleted address object with the none address object in the referenced firewall policy FortiManager will replace the deleted address object with all address object in the referenced firewall policy.
Which three settings are the factory default settings on FortiManager? (Choose three.) Username is admin Password is fortinet FortiAnalyzer features are disabled Reports and Event Monitor panes are enabled port1 interface IP address is 192.168.1.99/24.
In the event that the primary FortiManager fails, which of the following actions must be performed to return the FortiManager HA to a working state? Secondary device with highest priority will automatically be promoted to the primary role, and manually
reconfigure all other secondary devices to point to the new primary device Reboot one of the secondary devices to promote it automatically to the primary role, and reconfigure all
other secondary devices to point to the new primary device. Manually promote one of the secondary devices to the primary role, and reconfigure all other secondary
devices to point to the new primary device. FortiManager HA state transition is transparent to administrators and does not require any reconfiguration.
Which two conditions trigger FortiManager to create a new revision history? (Choose two.) When configuration revision is reverted to previous revision in the revision history When FortiManager installs device-level changes to a managed device
When FortiManager is auto-updated with configuration changes made directly on a managed device When changes to device-level database is made on FortiManager.
What will happen if FortiAnalyzer features are enabled on FortiManager? FortiManager will reboot FortiManager will send the logging configuration to the managed devices so the managed devices will start sending logs to FortiManager FortiManager will enable ADOMs automatically to collect logs from non-FortiGate devices FortiManager can be used only as a logging device.
Which two statements are true if the script is executed using the Remote FortiGate Directly (via CLI) option? (Choose two.) You must install these changes using Install Wizard. FortiGate will auto-update the FortiManager’s device-level database. FortiManager will create a new revision history. FortiManager provides a preview of CLI commands before executing this script on a managed FortiGate.
An administrator with the Super_User profile is unable to log in to FortiManager because of an authentication failure message.
Which troubleshooting step should you take to resolve the issue? Make sure FortiManager Access is enabled in the administrator profile Make sure Offline Mode is disabled Make sure the administrator IP address is part of the trusted hosts. Make sure ADOMs are enabled and the administrator has access to the Global ADOM.
An administrator is importing a new device to FortiManager and has selected the shown options. What will happen if the administrator makes the changes and installs the modified policy package on this managed FortiGate? The unused objects that are not tied to the firewall policies will be installed on FortiGate The unused objects that are not tied to the firewall policies will remain as read-only locally on FortiGate The unused objects that are not tied to the firewall policies locally on FortiGate will be deleted The unused objects that are not tied to the firewall policies in policy package will be deleted from the
FortiManager database.
In addition to the default ADOMs, an administrator has created a new ADOM named Training for FortiGate devices. The administrator sent a device registration to FortiManager from a remote FortiGate. Which one of the following statements is true? The FortiGate will be added automatically to the default ADOM named FortiGate. The FortiGate will be automatically added to the Training ADOM. By default, the unregistered FortiGate will appear in the root ADOM The FortiManager administrator must add the unregistered device manually to the unregistered device
manually to the Training ADOM using the Add Device wizard.
An administrator created a new system template named Training with two new DNS addresses on FortiManager. During the installation preview stage, the administrator notices that many unset commands need to be pushed.
What can be the main reason for these unset commands? The DNS addresses in the default system settings are the same as the Training system template The Training system template has other default settings The ADOM is locked by another administrator The Training system template does not have assigned devices.
An administrator run the reload failure command:
diagnose test deploymanager reload config <deviceid> on FortiManager.
What does this command do? It downloads the latest configuration from the specified FortiGate and performs a reload operation on the device database. It installs the latest configuration on the specified FortiGate and update the revision history database. It compares and provides differences in configuration on FortiManager with the current running
configuration of the specified FortiGate. It installs the provisioning template configuration on the specified FortiGate.
Which two items are included in the FortiManager backup? (Choose two.) FortiGuard database Global database Logs All devices.
An administrator is replacing a device on FortiManager by running the following command:
execute device replace sn <devname> <serialnum>.
What device name and serial number must the administrator use? Device name and serial number of the original device. Device name and serial number of the replacement device Device name of the replacement device and serial number of the original device Device name of the original device and serial number of the replacement device.
Which of the following statements are true regarding VPN Manager? (Choose three.) VPN Manager must be enabled on a per ADOM basis. VPN Manager automatically adds newly-registered devices to a VPN community. VPN Manager can install common IPsec VPN settings on multiple FortiGate devices at the same time Common IPsec settings need to be configured only once in a VPN Community for all managed gateways. VPN Manager automatically creates all the necessary firewall policies for traffic to be tunneled by IPsec.
An administrator has added all the devices in a Security Fabric group to FortiManager.
How does the administrator identify the root FortiGate? By a dollar symbol ($) at the end of the device name By an at symbol (@) at the end of the device name By a QUESTION NO: mark(?) at the end of the device name By an Asterisk (*) at the end of the device name.
Which of the following statements are true regarding VPN Gateway configuration in VPN Manager? (Choose two.) Managed gateways are devices managed by FortiManager in the same ADOM External gateways are third-party VPN gateway devices only Protected subnets are the subnets behind the device that you don’t want to allow access to over the IPsec
VPN Managed devices in other ADOMs must be treated as external gateways.
What does a policy package status of Modified indicate? FortiManager is unable to determine the policy package status The policy package was never imported after a device was registered on FortiManager The Policy configuration has been changed on a managed device and changes have not yet been imported into FortiManager The Policy package configuration has been changed on FortiManager and changes have not yet been installed on the managed device.
Which of the following statements are true regarding schedule backup of FortiManager? (Choose two.) Backs up all devices and the FortiGuard database. Does not back up firmware images saved on FortiManager Supports FTP, SCP, and SFTP Can be configured from the CLI and GUI.
What does the diagnose dvm check-integrity command do? (Choose two.) Internally upgrades existing ADOMs to the same ADON version in order to clean up and correct the ADOM
syntax Verifies and corrects unregistered, registered, and deleted device states Verifies and corrects database schemas in all object tables Verifies and corrects duplicate VDOM entries.
An administrator would like to authorize a newly-installed AP using AP Manager.
What steps does the administrator need to perform to authorize an AP? Authorize the new AP using AP Manager and wait until the change is updated on the FortiAP. Changes to
the AP's state do not require installation. Changes to the AP's state must be performed directly on the managed FortiGate Authorize the new AP using AP Manager and install the policy package changes on the managed FortiGate Authorize the new AP using AP Manager and install the device level settings on the managed FortiGate.
An administrator would like to create an SD-WAN using central management. What steps does the administrator need to perform to create an SD-WAN using central management? First create an SD-WAN firewall policy, add member interfaces to the SD-WAN template and create a static
route You must specify a gateway address when you create a default static route Remove all the interface references such as routes or policies Enable SD-WAN central management in the ADOM, add member interfaces, create a static route and
SDWAN firewall policies.
An administrator used the value shown in the exhibit when importing a Local-FortiGate into FortiManager. What name will be used to display the firewall policy for port1? port1 on FortiGate and WAN on FortiManager port1 on both FortiGate and FortiManager WAN zone on FortiGate and WAN zone on FortiManager WAN zone on FortiGate and WAN interface on FortiManager.
An administrator would like to create an SD-WAN default static route for a newly created SD-WAN using the FortiManager GUI. Both port1 and port2 are part of the SD-WAN member interfaces.
Which interface must the administrator select in the static route device drop-down list? port2 virtual-wan-link port1 auto-discovery.
Which of the following statements are true regarding reverting to previous revision version from the revision history? (Choose two.) To push these changes to a managed device, it required an install operation to the managed FortiGate Reverting to a previous revision history will generate a new version ID and remove all other history versions Reverting to a previous revision history will tag the device settings status as Auto-Update It will modify device-level database.
An administrator has created a firewall address object, Training, which is used in the Local-FortiGate policy package. When the install operation is performed, which IP Netmask will be installed on the Local-FortiGate, for the Training firewall address object? 10.0.1.0/24 It will create firewall address group on Local-FortiGate with 192.168.0.1/24 and 10.0.1.0/24 object values 192.168.0.1/24 Local-FortiGate will automatically choose an IP Network based on its network interface settings.
Which configuration setting for FortiGate is part of a device-level database on FortiManager? VIP and IP Pools Firewall policies Security profiles Routing.
Which configuration setting for FortiGate is part of an ADOM-level database on FortiManager? NSX-T Service Template Security profiles SNMP Routing.
Which two statements regarding device management on FortiManager are true? (Choose two) FortiGate devices in HA cluster devices are counted as a single device. FortiGate in transparent mode configurations are not counted toward the device count on FortiManager. FortiGate devices in an HA cluster that has five VDOMs are counted as five separate devices. The maximum number of managed devices for each ADOM is 500.
|
