Questions
ayuda
option
My Daypo

ERASED TEST, YOU MAY BE INTERESTED ONFAA AMT GENERAL QUESTIONS 01

COMMENTS STATISTICS RECORDS
TAKE THE TEST
Title of test:
FAA AMT GENERAL QUESTIONS 01

Description:
faa study guide

Author:
fabio santos
(Other tests from this author)

Creation Date:
01/04/2017

Category:
Others

Number of questions: 40
Share the Test:
Facebook
Twitter
Whatsapp
Share the Test:
Facebook
Twitter
Whatsapp
Last comments
No comments about this test.
Content:
When computing the maximum forward loaded CG of an aircraft, minimum weights, arms, and moments should be used for items of useful load that are located aft of the: rearward CG limit. datum. forward CG limit.
Which heat treating operation would be performed when the surface of the metal is changed chemically by introducing a high carbide or nitride content? Normalizing. Case hardening. Tempering.
Which tubings have the characteristics (high strength, abrasion resistance) necessary for use in a high pressure (3,000 PSI) hydraulic system for operation of landing gear and flaps? 1100-1/2H or 3003-1/2H aluminum alloy. 2024-T or 5052-0 aluminum alloy. Corrosion resistant steel annealed or 1/4H.
(Refer to Figure 14 .) The total resistance of the circuit is: 35 ohms. 25 ohms. 17 ohms.
For sketching purposes, almost all objects are composed of one or some combination of six basic shapes; these include the: triangle, circle, cube, cylinder, cone, and sphere. angle, arc, line, plane, square, and circle. triangle, plane, circle, line, square, and sphere.
Through which material will magnetic lines of force pass the most readily? Aluminum. Iron. Copper.
A person should approach or leave a helicopter in the pilot's field of vision whenever the engine is running in order to avoid: blowing dust or debris caused by rotor downwash. the tail rotor. the main rotor.
The amount of fuel used for computing empty weight and corresponding CG is: unusable fuel. empty fuel tanks. the amount of fuel necessary for 1/2 hour of operation.
Flexible lines must be installed with: a slack of at least 10 to 12 percent of the length. enough slack to allow maximum flexing during operation. a slack of 5 to 8 percent of the length.
On a fillet weld, the penetration requirement includes what percentage(s) of the base metal thickness? 25 to 50 percent. 60 to 80 percent. 100 percent.
The following words are an example of what kind of statement in an AD? "Required within the next 25 hours time-in-service after the effective date of this AD, unless already accomplished." Amendment. Compliance. Applicability.
When a discrepancy list is provided to an aircraft owner or operator after an inspection, it says in effect that: the item inspected is unairworthy. except for these discrepancies, the item inspected is airworthy. the item inspected may or may not be airworthy depending on the discrepancies found.
A drawing in which the subassemblies or parts are shown as brought together on the aircraft is called: an installation drawing. an assembly drawing. a detail drawing.
(Refer to Figure 11 .) Find the voltage across the 8-ohm resistor. 24 volts. 20.4 volts. 8 volts.
The aluminum code number 1100 identifies what type of aluminum? Aluminum alloy containing zinc. 99 percent commercially pure aluminum. Aluminum alloy containing 11 percent copper.
Which number represents the vernier scale graduation of a micrometer? .0001. .001. .00001.
(Refer to Figure 40 .) Determine the proper tension for a 1/8-inch cable (7 x 19) if the temperature is 80 °F. 80 pounds. 70 pounds. 75 pounds.
(Refer to Figure 45 .) What type weld is shown at A? Fillet. Butt. Lap.
A complete detailed inspection and adjustment of the valve mechanism will be made at the first 25 hours after the engine has been placed in service. Subsequent inspections of the valve mechanism will be made each second 50-hour period.From the above statement, at what intervals will valve mechanism inspections be performed? 50 hours. 125 hours. 100 hours.
(Refer to Figure 37 .) The vertical distance between the top of the plate and the bottom of the lowest 15/64-inch hole is: 2.367. 2.242. 2.250.
(Refer to Figure 24 .) Which statement concerning the depicted logic gate is true? All inputs must be 1 to produce a 1 output. Any input being 1 will produce a 0 output. Any input being 1 will produce a 1 output.
Which is correct in reference to electrical resistance? An electrical device that has a high resistance will use more power than one with a low resistance with the same applied voltage. Two electrical devices will have the same combined resistance if they are connected in series as they will have if connected in parallel. If one of three bulbs in a parallel lighting circuit is removed, the total resistance of the circuit will become greater.
Where is an AN clevis bolt used in an airplane? Only for shear load applications. For tension and shear load conditions. Where external tension loads are applied.
When an aircraft is positioned for weighing on scales located under each landing gear wheel, which of the following may cause erroneous scale readings? Gear downlocks installed. Parking brakes set. Parking brakes not set.
An Airworthiness Directive requires that a propeller be altered. Certificated mechanics could: not perform the work because it is an alteration. not perform the work because they are not allowed to perform and approve for return to service, repairs or alterations to propellers. perform and approve the work for return to service if it is a minor alteration.
Under magnetic particle inspection, a part will be identified as having a fatigue crack under which condition? The discontinuity is found in a highly stressed area of the part. The discontinuity is found in a nonstressed area of the part. The discontinuity pattern is straight.
A mechanic has completed a bonded honeycomb repair using the potted compound repair technique. What nondestructive testing method is used to determine the soundness of the repair after the repair has cured? Metallic ring test. Eddy current test. Ultrasonic test.
Select the container size that will be equal in volume to 60 gallons of fuel.(7.5 gal = 1 cu ft). 8.5 cubic feet. 8.0 cubic feet. 7.5 cubic feet.
(1) Bonded clamps are used for support when installing metal tubing.(2) Unbonded clamps are used for support when installing wiring.Regarding the above statements, both No. 1 and No. 2 are true. only No. 1 is true. neither No. 1 nor No. 2 is true.
(Refer to Figure 54 .) Compute the area of the trapezoid. 60 square feet. 52.5 square feet. 76.5 square feet.
The speed of sound in the atmosphere is most affected by variations in which of the following? 1. sound frequency (cps) 2. ambient temperature 3. barometric pressure 1 2 3.
The boiling point of a given liquid varies: directly with pressure inversely with pressure directly with density.
An engine that weighs 350 pounds is removed from an aircraft by means of a mobile hoist. The engine is raised 3 feet above its attachment mount, and the entire assembly is then moved forward 12 feet. A constant force of 70 pounds is required to move the loaded hoist. What is the total work input required to move the hoist? 840 foot-pounds 1,890 foot-pounds 1,050 foot-pounds.
How much work is required to lower (not drop) a 120-pound weight from the top of a 3-foot table to the floor? 120 foot-pounds of force 360 foot-pounds 40 foot-pounds.
In physics, which of the following factors are necessary to determine power? 1. force exerted 2. distance moved 3. time required 1 and 2 2 and 3 1, 2, and 3.
Which of the following is Newton´s first law of motion, generally termed the law of inertia? to every action there is an equal and opposite reaction force is proportional to the product of mass and acceleration every body persists in its state of rest, or of motion in a straight line, unless acted upon by some outside force.
What force must be applied to roll a 120-pound barrel up an inclined plane 9 feet long to a height of 3 feet (disregard friction)? L / I = R / E L= length of ramp, measured along the slope I= height of ramp R= weight of object to be raised or lowered E= force required to raise or lower object 40 pounds 120 pounds 360 pounds.
(Refer to figure 61.) The amount of force applied to rope A to lift the weight is: 12 pounds 15 pounds 20 pounds.
Which statement concerning Bernoulli´s principle is true? the pressure of a fluid increases at points where the velocity of the fluid increases the pressure of a fluid decreases at points where the velocity of the fluid increases it applies only to gases.
What force is exerted on the piston in a hydraulic cylinder if the area of the piston is 1.2 square inches and the fluid pressure is 850 PSI? 1,020 pounds 960 pounds 850 pounds.
Report abuse Consent Terms of use