Questions
ayuda
option
My Daypo

ERASED TEST, YOU MAY BE INTERESTED ONFAA AMT GENERAL QUESTIONS 04

COMMENTS STATISTICS RECORDS
TAKE THE TEST
Title of test:
FAA AMT GENERAL QUESTIONS 04

Description:
faa study guide

Author:
fabio santos
(Other tests from this author)

Creation Date:
07/04/2017

Category:
Others

Number of questions: 40
Share the Test:
Facebook
Twitter
Whatsapp
Share the Test:
Facebook
Twitter
Whatsapp
Last comments
No comments about this test.
Content:
14 CFR Part 65 contains information for the certification of: pilots, flight Instructors, and ground instructors airmen other than flight crewmembers flight crewmembers other than pilots.
What does the acronym TSO mean regarding a type certificated aircraft part, material, component and/or process? Training Specific Organization. Type Supplement Original. Technical Standard Order.
The main rotor system on a helicopter is classified in three groups. Which of those listed is NOT one of these groups? The fully articulated rotor system The flexible-beam rotor system The semi-rigid rotor system.
Examples of units used in the conventional (U.S. or English) measurement include: inch, meter, and rod. inch, kilometer, and fraction. inch, feet, and yard.
Convert 7 to binary form. 0111. 0011. 1110.
If an engine fire develops during the starting procedures, the first step you should take in extinguishing the fire is: discontinue the start attempt and allow the fireguard to extinguish the fire using the available equipment continue cranking to start the engine and blow out the fire continue cranking and allow the fireguard to extinguish the fire using the available equipment.
Where do you look to determine the operating CG range when calculating a new aircraft weight and balance document? It is found on the airframe data plate. It is found in the type certificate data sheet. It is found in the pilot’s aircraft information manual.
What is meant by the term “residual fuel”? A known amount of fuel left in the tanks, lines, and engine The fuel remaining in the tanks, lines, and engine after draining. The fuel remaining in the tank, lines, and engine before draining.
What type of drawing line consists of alternating long and short lines? Dimension. Center. Hidden.
(1) A Supplemental Type Certificate may be issued to more than one applicant for the same design change, providing each applicant shows compliance with the applicable airworthiness requirement.(2) An installation of an item manufactured in accordance with the Technical Standard Order system requires no further approval for installation in a particular aircraft.Regarding the above statements, neither No. 1 nor No. 2 is true. both No. 1 and No. 2 are true. only No. 1 is true.
The following alteration was performed on an aircraft: A model B engine weighing 175 pounds was replaced by a model D engine weighing 185 pounds at a -62.00 inch station. The aircraft weight and balance records show the previous empty weight to be 998 pounds and an empty weight CG of 13.48 inches. What is the new empty weight CG? 14.25 inches. 12.73 inches. 13.96 inches.
The potential difference between two conductors which are insulated from each other is measured in: volts. coulombs. amperes.
When determining the empty weight of an aircraft, certificated under current airworthiness standards (14 CFR Part 23), the oil contained in the supply tank is considered: a part of the useful load. the same as the fluid contained in the water injection reservoir. a part of the empty weight.
Instrument repairs may be performed: on airframe instruments by mechanics with an airframe rating. by an FAA-approved instrument repair station. by the instrument manufacturer only.
An airplane flying a distance of 875 miles used 70 gallons of gasoline. How many gallons will it need to travel 3,000 miles? 250. 144. 240.
In nickel cadmium batteries, a rise in cell temperature: causes a decrease in internal resistance. causes an increase in internal resistance. increases cell voltage.
Express 7/8 as a percent. 8.75 .875 87.5.
What is the speed of a spur gear with 42 teeth driven by a pinion gear with 14 teeth turning 420 RPM? 588 RPM 160 RPM 140 RPM.
An engine develops 108 horsepower at 87 percent power. What horsepower would be developed at 65 percent power? 80 70 64.
A certain aircraft bolt has an overall length of 1-1/2 inches, with a shank length of 1-3/16 inches, and a threaded portion length of 5/8 inch. What is the grip length? .5625 inch .8750 inch .3125 inch.
Select the fractional equivalent for a 0.0625 inch-thick sheet of aluminum. 1/16 1/32 3/64.
Under which conditions will rate of flow of a liquid through a metering orifice (or jet) be the greatest (all other factors being equal)? unmetered pressure - 18 PSI, metered pressure - 17,5 PSI, atmospheric pressure - 14,5 PSI unmetered pressure - 23 PSI, metered pressure - 12 PSI, atmospheric pressure - 14,3 PSI unmetered pressure - 17 PSI, metered pressure - 5 PSI, atmospheric pressure - 14,7 PSI.
If the volume of a confined gas is doubled (without the addition of more gas), the pressure will (assume the temperature remains contant). increase in direct proportion to the volume increase remain the same be reduced to one-half its original value.
If the temperature of a confined liquid is held constant and its pressure is tripled, the volume will: triple be reduced to one-third its original value remain the same.
If the fluid pressure is 800 PSI in a 1/2-inch line supplying an actuating cylinder with a piston area of 10 square inches, the force exerted on the piston will be: 4,000 pounds 8,000 pounds 800 pounds.
Which statement concerning heat and/or temperature is true? there is an inverse relationship between temperature and heat temperature is a measure of the kinetic energy of the molecules of any substance temperature is a measure of the potential energy of the molecules of any substance.
(Refer to figure 18.) The control valve switch must be placed in the neutral position when the landing gears are down to: remove the ground from the green light permit the test circuit to operate prevent the warning horn from sounding when the throttles are closed.
(Refer to figure 45.) What type weld is shown at G? butt joint lap.
(Refer to figure 6.) If resistor R5 is disconnected at the junction of R4 and R3 as shown, what will the ohmmeter read? 3 ohms 2.76 ohms 12 ohms.
Which tool is used to find the center of a shaft or other cylindrical work? combination set dial indicator micrometer caliper.
Which of the following hose materials are compatible with phosphate-ester base hydraulic fluids? 1. butyl 2. teflon 3. bruna-n 4. neopreme 1 and 2 2 and 4 1 and 3.
A part which is being prepared for dye penetrant inspection should be cleaned with: water-base solvents only the penetrant developer a volatile petroleum-base solvent.
The empty weight of an airplane is determined by: subtracting the tare weight from the scale reading and adding the weight of each weighing point multiplying the measured distance from each weighing point to the datum times the sum of scale reading less the tare weight adding the net weight of each weighing point and multiplying the measured distance to the datum.
(Refer to figure 23.) If an open occurs at R1, the light: cannot be turned on will not be affected cannot be turned off.
Scratches or nicks on the straight portion of aluminum alloy tubing may be repaired if they are no deeper than: 10 percent of the wall thickness 20 percent of the wall thickness 1/32 inch or 20 percent of wall thickness, whichever is less.
The pattern for an inclusion is a magnetic particle buildup forming: a single line parallel lines a fernlike pattern.
(Refer to figure 36.) The vertical distance between the top of the plate and the bottom of the lowest 15/64-inch hole is: 2.250 2.242 2.367.
(Refer to figure 34.) What is the dimension of the chamfer? 0.3125 + .005 -0 0.3125 + .005 -0° 0.0625 X 45°.
If it is necessary to accurately measure the diameter of a hole approximately 1/4 inch in diameter, the mechanic should use a: small-hole gauge and determine the size of the hole by taking a micrometer reading of the ball end of the gauge telescoping gauge and determine the size of the hole by taking a micrometer reading of the adjustable end of the telescoping gauge 0 to 1-inch inside micrometer and read the measurement directly from the micrometer.
(Refer to figure 44.) Identify the weld caused by an excessive amount of acetylene. 3 4 1.
Report abuse Consent Terms of use